掃一掃，關注我們
微信公眾號：
SCR-LA系列單相固態繼電器產品型號大全:SCR-10LA/SCR-25LA/SCR-40LA/SCR-50LA/SCR-75LA/SCR-10LA-H/SCR-25LA-H/SCR-40LA-H/SCR-50LA-H/SCR-75LA-H
■ Specification【Rated current corresponding to Resistive load】
| Type 型式 | Standard type / 標準型 | |||||||
| Model 型號 | SCR – 10LA | SCR – 25LA | SCR – 40LA | SCR – 50LA | SCR – 75LA | |||
| Rated current 額定電流 | 10A max. | 25A max. | 40A max | 50A max. | 75A max | |||
| I2t for fuse 熔斷電流 | 144A2S | 259A2S | 664A2S | 518A2S | 1328A2S | |||
| Surge current 耐突波電流 | 135A | 275A | 410A | 550A | 820A | |||
| Peak voltage 耐突波電壓 | 1200VAC min. | |||||||
| Output voltage 輸出電壓 | 90 ~ 250VAC | |||||||
| Type 型式 | High voltage type / 高壓型 | |||||||
| Model 型號 | SCR – 10LA-H | SCR – 25LA-H | SCR – 40LA-H | SCR – 50LA-H | SCR – 75LA-H | |||
| Rated current 額定電流 | 10A max. | 25A max. | 40A max | 50A max. | 75A max | |||
| I2t for fuse 熔斷電流 | 144A2S | 259A2S | 664A2S | 518A2S | 1328A2S | |||
| Surge current 耐突波電流 | 135A | 275A | 410A | 550A | 820A | |||
| Peak voltage 耐突波電壓 | 1200VAC min. | |||||||
| Output voltage 輸出電壓 | 250 ~ 480VAC | |||||||
■General specification / 共同規格
| 輸入方式 | 4 ~ 20 mA | ||||
| 輸入阻抗 | Approx. 1.2KΩ | ||||
| 控制方式 | Phase control | ||||
| 洩漏電流 | 0.5% of full load max. | ||||
| 反應時間 | 1.0ms max. | ||||
| 輸入耐突波 | 4 KVrms（EN60950/VDE0805） | ||||
| 電介強度 | 100MΩ / 500VDC（EN60950/VDE0805） | ||||
| 絕緣強度 | 100MΩ / 500VDC（EN60950/VDE0805） | ||||
| 外殼材質 | 防火ABS（UL: 94V0） | ||||
| 工作環境 | -40℃ ~ +80℃；35 ~ 85％RH | ||||
■ Notice of safety / 安全注意事項
Warning
Potentially hazardous situation, if mishandling, may result in death or serious injury.
潛在危險，如果操作失當可能導致死亡或嚴重傷害。
1＞ Please do not touch any terminal of this module while power supply is supplied, if do, it may result in electronic shock.
送電中，請勿碰觸本固態模組任何接線端子以避免觸電。
2＞ 「Power supply system」must to be shutdown before renew the fuse, if not, it may result in electronic shock.
更換保險絲前，請務必關閉電源系統以避免觸電。
3＞ Please rated the load current within the specified value, if not, it may result to burn up this module or fuse.
負載電流請勿超過額定電流，以避免保險絲或本固態模組燒毀。
4＞ Please tighten the screw terminal over 100kg-cm, if not, it may result to burn up this module or fuse.
請務必鎖緊端子螺絲，扭力須超過100kg-cm，否則可能導致本固態模組或保險絲燒毀。
5＞ If this module is burned up, it may be in short circuit condition or malfunction, Please settle an independent alarm
system to ensure safety protection, if not, it may result in a serious accident.
本固態模組燒毀後可能是短路或失控狀態，請加裝獨立警報系統以確保安全， 否則可能造成嚴重意外事故。
■ Notice of use / 使用注意事項
1＞ To protect the solid state module against a short-circuit of the load, please use a fuse with a I2t value ＜ 1/2 I2t
value specified.
請加裝快速保險絲（I2t value 小於額定值的一半），以防止因負載短路而造成固態模組燒毀。
2＞ The thermal conductive silicone rubber or thermal grease is required
When the solid state module is mounted on a heat sink
本固態模組加裝散熱器時務必墊高導熱系數的矽膠片或散熱膏【導熱系數（K）＞4.5】。
3＞ The rated current is corresponding to a resistive load, if the solid state module is applied in other loads,
Please consider the inrush current at turn on and the surge voltage at turn off.
本固態模組所標示的額定電流是以電阻性負載為準，如果使用在其他負載上須考慮起動電流及關機突波。
＊ Electric discharge lamps: Those loads have the「inrush current」at turn on and the「surge voltage」at turn off,
please use「high voltage type」on 220VAC mains.
電子起動式燈具（如日光燈）：須考慮起動電流及關機突波，220VAC電源系統請選用「高壓型」。
＊ Incandescent lamp: The rated current of the module must be over 4 times of the incandescent lamp current.
炙熱燈泡（如IR燈管）： 須考慮起動電流，固態模組的額定電流須大於炙熱燈泡電流的「四倍」。
＊ Three phase motors: The rated current of the s module must be over 4 times of the three phase motor average
current .
三相馬達：須考慮起動電流，固態模組的額定電流須大於三相馬達平均電流的「四倍」。
＊ Transformer loads: The rated current of the module must be over 10 times of the transformer current.
變壓器負載：須考慮反電動電流，固態模組的額定電流須大於變壓負載電流的「十倍」。
＊ Capacitor loads, the rated current of the module must be over 3 times of the capacitor current .
電容性負載：須考慮充電瞬間電流，固態模組的額定電流須大於電容性負載電流的「三倍」。
客服QQ